Industrial & Scientific From MakerFocus on Amazon

M5 Stack ESP32 E-Ink GT911 M5 Paper V1.1 with 540*960 4.7 inch New Upgraded Flexible E-Ink Screen Multi-Touch Screen WiFi Bluetooth Built-in 16M Flash 1150mAh Battery for Ar duino UIFlow MicroPython

Ratings for MakerFocus (CPR Score)

MakerFocus 4pcs 3D Printer Fan 12V, 40mm 12 Volt Fan 0.08A DC Mini Quiet Cooling Fan 40X40X10mm with 28cm Cable for 3D Printer, DVR and Other Small Appliances Series Repair Replacement

Ratings for MakerFocus (CPR Score)

Features

Size: 40 mm x 40 mm x 10 mm; Working Voltage: DC 12V.

Temperature of usage environment: -10℃ to +70℃.

Show More

MakerFocus 2pcs Raspberry Pi Fan 30x 30mm DC Brushless Cooling Fan Heatsink Cooler Radiator One-to-Two Interface 3.3V 5V for Raspberry Pi 4 Pi 3 3B+ and Pi Zero/Zero W or Other Robot Project

Ratings for MakerFocus (CPR Score)

Features

√. Installation Screws Included: Don't need to purchase screws by yourself. Intimate service, easy to install!

√. Super Quiet: This fan will not make you feel uneasy during they are working, but also a quiet experiment environment for you. Perfect Cooling Tool: Allows your Raspberry Pi or other experimental tools to quickly dissipate heat and will extend the working life of your Pi or other development boards!

Show More

DIY Electronic Clock Module Kit -MakerFocus Digital LED Display PCB Soldering Project Learning Board with Battery Holder for Beginner Welding Learner

Ratings for MakerFocus (CPR Score)

MakerFocus 3pcs Mini Digital DC Voltmeter 0.28 Inch Two-Wire 3.0V-30V Digital DC Waterproof, Dustproof and Drop Resistant Voltmeter Display Voltage Tester Meter 3 Colours(Red, Green, Yellow)

Ratings for MakerFocus (CPR Score)

Features

This is a great Mini Digital DC Voltmeter with new features: Waterproof, dustproof and drop resistant.

The decimal point is automatically shifted. When the voltage below 10V, the number of digits displayed on the voltmeter is 0.01; When higher than 10V, the number of digits displayed on the voltmeter is 0.1 and is automatically shifted.

Show More

DIY Flashing Led Light Kit - MakerFocus Red Blue Water Lamp Soldering Practice Board PCB for Kids Beginners to Learn with Power Cord Battery Box

Ratings for MakerFocus (CPR Score)

MakerFocus TFmini-s Micro Lidar Module 0.1-12M Lidar Range Finder Sensor Obstacle Avoidance Sensor Tiny Module 1000Hz Single Point UART I2C IO Compatible with Pixhawk Ar duino and Raspberry Pi

Ratings for MakerFocus (CPR Score)

Features

★ ★ Note: TFmini-s version is UART by default. If you need I2C, please switch by yourself. It is compatible with Raspberry Pi and Arduino. ★ User Manual and Document: Please get the link from Product guides and documents below

Upgraded Lidar Module: TFmini-s is an upgraded single-point micro ranging module based on TFmini. The dead zone is shortened to 10 cm, and the outdoor performance and accuracy of different reflectances are improved

Show More

MakerFocus 2pcs I2C OLED Display Module 0.91 Inch I2C SSD1306 OLED Display Module Blue I2C OLED Screen Driver DC 3.3V~5V for Ar duino

Ratings for MakerFocus (CPR Score)

Features

Product manual: Please get the link from Product guides and documents below

OLED display, no need backlight, self-illumination, Display Color: Blue. Plz note: These I2C OLED Display Module comes without pin headers

Show More

MakerFocus TFT LCD Screen Display 1.3inch TFT LCD Module, 240x240 IPS 65K Full Color 3.3V with SPI Interface ST7789 IC Driver, 51 STM32 Ar duino Routines for DIY

Ratings for MakerFocus (CPR Score)

Features

1.3inch TFT LCD Screen Display Module:The TFT display provides a semiconductor switch for each pixel and each pixel is directly controlled by pulse. Therefore, each node is relatively independent and can be continuously controlled, which not only improves the response speed of the display, but also can be accurately controlled

Dot Size: 240*240 (There are two display way: horizontal display and vertical display, you can adjust the display direction.)

Show More

Makerfocus 4pcs ESP8266 Esp-01 Serial Wireless Wifi Transceiver Module Compatible with Arduino

Ratings for Makerfire (CPR Score)

Features

Note:The test template tutorial is available in the product guide . There are a batch of this ESP01 modules are the new grade version. Maybe there are some different between the new one and old one in the aspect of usage. Pls feel free to email us if you have any question about how to use the new vertion module. How to email us? Click "MakerFocus" and click "Ask a question". There is the way to guide you to use the new version in the pictures, pls refer to the pictures carefully.

Version II to test this module youtube tutorial and the Link to view the technical details, Please get the link from the product description below

Show More