Industrial & Scientific From Fulton on Amazon

The 6 included scrapers are made from a strong carbon steel and come in various shapes for a wide variety of applications. The three rectangle scrapers of various thicknesses in this pack will work for the vast majority of your projects. The curved (convex and concave curves), gooseneck and beveled scrapers are ideal for working oddly shaped pieces like chairs, spindles, boxes and more.

If you have never used a burnisher, it is relatively simple to use. The idea is to roll the edges of your scraper to create a burr so that it produces fine, light shavings and makes the wood surface very smooth. To do this, you simply tilt the burnisher slightly to one side of the scraper and run the burnisher along the edge repeatedly until you produce the burr you are looking for.

Once your scrapers have the desired burr on each edge, you’ll be able to produce wonderful looking results on your wooden surfaces. Scrapers are perfect making your surfaces extra smooth and ready for light sanding for the finishing process. We highly recommend burnishing each scraper out of the box for optimum performance. Also included is a handy booklet on “How to Sharpen a Card Scraper Using A Burnisher” to get you started right out of the box.

One of the most common uses for the forstner bit extension is for woodturners who need to bore out starter holes on larger vessels. However, the extension works exceptionally well for projects like salt shakers, pepper mills or even wood turned beverage mugs. Contractors use the extension when they need to bore deep holes for running cables or wires and they also use it for joining larger timbers.

The forstner bit extender is made from solid, heavy duty machined steel. It is designed to be used with forstner bits only. The collet inside diameter is 3/8 inch. This tolerance is very tight and designed to accept forstner bits with shank sizes of 3/8 inch or slightly smaller. Please note that some forstner bit manufacturers produce bits that say 3/8 inch shank size when in fact they are not. If you measure your bit shank and it is 3/8 inch, your bit should fit once the set screws are loosened

The collet outside diameter is 25/32 inch without the set screws protruding outward. The reason this is important is that as we mentioned earlier, some bits may have slightly different shank sizes. This means the set screws may protrude outwardly from the collet. The minimum size hole this extension will allow you to drill is 13/16 inch. Forstner bits and Machinery shown in pictures are NOT included.

Once you have the clamp tips spread apart, simply place the spring clamp onto the mitered corner you need to secure, then release the clamp so the tips pierce into the wood and keep your stock in place. Depending on the size of your project, you may need to use more than one spring clamp on each corner to hold your stock in place.

Unlike other available spring clamps, the Fulton Miter Spring Clamps don’t cut into your stock piece. The uniquely designed tips are designed to pierce the wood so that there is minimal visible evidence of the clamps being used after you remove them. Other brands of spring clamp use a one sided cut on the clamp tip which pushes, cuts and tears at the wood which tends to leave harsh looking blemishes once the clamp is removed.

These spring miter clamps are perfect for carpenters, contractors, woodworking enthusiasts, art and craft hobbyists and more. Clamp picture frames, moldings, octagons and more with confidence. The clamps work perfectly with the Fulton Miter Spring Pliers and can be used on a wide variety of of wooden materials. Made in the USA

The Contour Sanding Grip pads are double-ended to make it super easy to sand convex or concave surfaces. Each pad has a convex profile at one and a concave profile at the other along with a narrow flexible section in the middle that can be used for sanding

Our Angled Contour Grip sanding pads change the angle sanding game by providing you the ability to sand inside angles without flattening or smoothing the crispness of your original profile. Not only does this set contain inside angle profile pads, there are 1/8” and ¼” round overs, various non specific round over profile and of course the flat sanding grip to sand general shapes and objects.

This 11pc set comes with the following: 2.6mm thick flexible pad, 1/8” and ¼” radius round over grip, 90 degree grip, 60 and 75 degree grip, 30 and 45 degree grip and 1 each contour grips with the following inside/outside diameters: 1/4'', 3/8'', 1/2'', 5/8'', 3/4'' and 7/8''.

Install the switch near or at hip level or in a position that you will be able to bump it when needed. The switch comes with installation hardware and can be mounted to most any type of material. The unit has two cords. The heavy duty female cord is 18” long and designed to accept the power source plug from your power tool. The heavy duty male cord is approximately 66 inches long and is used to plug the switch unit into your standard wall outlet.

Please take note that the Paddle Button Stop Power Tool Switch is 15 amps and will not work with power tools drawing higher amperage. Keep this in mind when connecting to your machinery. This switch was designed to work with smaller machinery like routers and smaller table saws. Check your machinery before using this product.

The stop sign paddle measures approximately 5-3/8” tall by 3-7/16” wide to make it easy to see and even easier to contact when needed. Mounting hardware is included but some surfaces my require hardware that does not come with the switch for proper mounting.

Bosch insert insert fits various Bosch models of table saws.

Includes leveling screws, side and end adjustment screws; rear safety tab; pre-cut blade bottom pocket

Please check your Length x Width x Thickness of your current insert before ordering to ensure that you get the correct insert.

One of the most common uses for the forstner bit extension is for woodturners who need to bore out starter holes on larger vessels. However, the extension works exceptionally well for projects like salt shakers, pepper mills or even wood turned beverage mugs. Contractors use the extension when they need to bore deep holes for running cables or wires and they also use it for joining larger timbers.

The forstner bit extender is made from solid, heavy duty machined steel. It is designed to be used with forstner bits only. The collet inside diameter is 3/8 inch. This tolerance is very tight and designed to accept forstner bits with shank sizes of 3/8 inch or slightly smaller. Please note that some forstner bit manufacturers produce bits that say 3/8 inch shank size when in fact they are not. If you measure your bit shank and it is 3/8 inch, your bit should fit once the set screws are loosened

The collet outside diameter is 25/32 inch without the set screws protruding outward. The reason this is important is that as we mentioned earlier, some bits may have slightly different shank sizes. This means the set screws may protrude outwardly from the collet. The minimum size hole this extension will allow you to drill is 13/16 inch. Forstner bits and Machinery shown in pictures are NOT included.