Sports & Outdoors From Case Club on Amazon

Accommodates full size, compact & subcompact pistols with under-barrel attachments and small reflex sights. Foam also has built-in height and length adjustment blocks in which you can use to further customize the fit ensuring even your smallest subcompact pistols fit just as tightly as your full size ones. Max length of pistols is 8 5/8" & is not intended for revolvers due to their longer barrel lengths.

Easily convert the case from a 6 pistol version to a 5 pistol & accessory version by removing the pistol module & freeing up room for ammunition & safety gear. Quickly convert it back to the 6 pistol version anytime by putting the module back in. Dual purpose foam design allows for two different configurations for the price of one!

Pistols sit in a quick draw position so the guns can be picked up properly by their grip in a safe manner. Wide bodied snap latches can be used with thick gloves. Extended front handle length helps counter balance off center weighted loads. All latch & hinge pins are stainless steel. Injected molded case shell with integrated exterior structural ribs increase durability and provide deflection points making this fully ATA approved and compliant in all 50 states.

Foam can be cut with a razor blade, electric carving knife or hot wire (not included)

After being cut down this will fit all major rifle cases including Pelican 1700, 1720, or 1747

DO NOT SETTLE for cheap and flimsy diced foam! Diced foam tears easily, retains water (rust!), collects dirt, and even if left untouched will eventually DISINTIGRATE right into your gun! Case Club foam is closed-cell military-grade polyethylene, which does NOT absorb liquids, does NOT tear easily, lasts a lifetime, can be cleaned easily, and will NOT disintegrate.

Two padlock points that support a customer supplied padlock with a 1/4" shackle along with one way hinge pins ensure your gear remains safe and secure.

Case has a lifetime warranty, is 100% Waterproof (IP67) & Dustproof with a built-in pressure release valve. Base foam is heavy duty, non-abrasive, pre-cut, mil-spec, closed cell polyethylene which won't absorb moisture or oil.

Magazine compartments are dual level & will fit both single & double stack mags of varying lengths. Utilize our specially designed magazine spacers for your single stack mags and remove the spacer for double stack guaranteeing a perfect fit regardless of magazine size.

A cutting blade is included for easy foam modifications to fit your specific setup!

Foam is closed cell military grade polyethylene that can be wiped clean

Case is watertight, airtight, packlockable, and has a pressure relief valve

Gun, and gun accessories depicted in pictures are not included

Twin side pockets store 6 extra magazines each along with all your gear

Pull-out rain cover protects gear in case of a sudden downpour

Built in Molle straps allow you to attach extra gear to the outside

The case is waterproof, dustproof and crushproof with a lifetime warranty. It is airline approved for checked luggage and a legal for vehicle transport in all 50 states. 2 metal reinforced padlock holes will take a customer supplied padlock and ensures nobody gets in without authorization. Fold down handle stays out of the way when not in use & has a molded texture which provides a comfortable grip. Built in lid-stay ensures the lid stays upright when open and metal pins make the hinges robust.

Outside ribs on the case deflect impact when being shipped and wide latches allow the case to be opened with thick gloves. A manual pressure release valve will allow you to equalize the atmospheric pressure when traveling to higher elevation.

The inside foam is military grade closed cell polyethylene which can be wiped down if it gets wet or oily. Don't settle for a flimsy case with pluck foam. This case is laser cut ready to go specifically for your pistol. Perfect for offroaders, campers, concealed permit holders, law enforcement & safe weapon storage.

Foam is closed cell military grade polyethylene that can be wiped clean

Built-in manual pressure release valve so the case can be opened in any altitude

Spotting Scope not included, this item is only the Case with Pre-Cut Foam

Foam insert is (closed cell) military grade polyethylene which is long lasting and can be wiped clean

The case comes with 9mm cutting blade for easy foam modifications, which works perfectly with the pre-cut perforations. The case also comes with silica gel to help prevent rust

The case is waterproof, airtight, has padlock holes, and a pressure relief valve

Has built-in metal reinforced padlockable holes, wheels, and a manual pressure relief valve

Case comes with a Lifetime Warranty

All the foam is Pre-Cut (see line drawing) so you get a custom foam fit at non-custom pricing!

Foam insert is (closed cell) high grade polyethylene which can be wiped clean

Built in padlockable holes for extra security. Case will not fit .308 style mags. Airsoft rifle, pistol, and accessories not included. Case is not waterproof.